Home / Setup guides / Corridor mapping

Corridor mapping: split a KML and place GCPs

Split a long corridor KML into DJI Pilot 2 flights, then lay out ground control that keeps the whole model true. Imperial spacing, with sources.

Have the corridor KML already? The free drone mission planner splits it into equal DJI Pilot 2 flights and lays out GCP, check shot and base pins across the whole job. Your file stays on your device.

Roads, pipelines, canals and power lines are long and thin. A corridor that runs for miles will not fit in one battery or stay within sight of the pilot, and ground control laid in a single line lets the model tip. This guide pulls together published field guidance from Aerotas, Propeller and the FHWA into a plan you can run with the FixFinder mission planner. Distances are in feet first.

The plan at a glance

  1. Start from one corridor file. Draw the road, pipeline or power line as a line or polygon in Google Earth or your CAD or GIS software and save it as KML or KMZ. Drop it into the drone mission planner and set the full corridor width you plan to fly.
  2. Split it into flights. Split the corridor into equal sections so each one fits a battery and stays within visual line of sight. The planner suggests no more than 3,000 ft per section and writes one boundary file per flight.
  3. Load each section into DJI Pilot 2. Copy a section file to the controller's SD card, then in DJI Pilot 2 tap Flight Route, Import Route (KMZ/KML), pick the file and choose the mapping mission type. Pilot 2 draws the flight lines over the boundary.
  4. Place GCPs across the whole job. Plan ground control once for the full corridor, in pairs on both edges, so pins near a seam count for both flights. Space pairs 500 to 1,000 ft apart without RTK on the drone, wider with RTK.
  5. Add check shots and bases. Put check shots inside the project area between GCPs, and plan where your GNSS base or network will cover the ground survey, ideally within about 12 miles.
  6. Fly the sections back to back. Fly neighboring sections in similar light, with about 100 ft of overlap between them and at least one GCP in each overlap.

1. Start from one corridor file

Draw the centerline or outline in Google Earth, CAD or GIS and save it as KML or KMZ. In the mission planner, a line becomes a corridor of the full width you enter, edge to edge, with your line down the middle. Aerotas describes typical linear jobs as 50 to 500 ft wide and often miles long.

2. Split the KML into flights

Under FAA Part 107, the pilot or visual observer must be able to see the drone throughout the flight (14 CFR 107.31). Aerotas notes most small drones become hard to see past about 1,500 ft, so it suggests taking off from the middle of a segment about twice your visual range, and says you can skip segmenting only when the whole corridor is under 3,000 ft or fits the batteries you have.

The mission planner splits a corridor into equal sections by length or area, and suggests no more than 3,000 ft per section to keep each flight manageable for battery, signal and file size (a common field recommendation, not a published standard). It writes one boundary file per section for DJI Pilot 2, DJI FlightHub 2 or Google Earth. Where sections meet, Aerotas recommends about 100 ft of overlap and at least one GCP in the overlap so the pieces stitch without a step.

3. Load each section into DJI Pilot 2

Copy one section file to the controller's SD card. In DJI Pilot 2, tap Flight Route, then Import Route (KMZ/KML), choose the file and pick the mapping mission type when asked. Pilot 2 generates flight lines to cover the boundary; then set height and overlap. Aerotas recommends flying lines lengthwise down the corridor, at least 3 lines, with 75% front and side overlap, and Propeller recommends at least four runs along a long, thin corridor. Part 107 generally caps altitude at 400 ft above ground level (14 CFR 107.51).

4. Place GCPs in pairs, not a single line

GCPs laid in one straight row let the model roll, like a board balanced on a string. Aerotas and Propeller both recommend a "ladder": a GCP on each edge of the corridor, repeated along its length.

DronePair spacing along the corridorSource
No RTK or PPK, flying at 150 ftAbout every 500 ftAerotas
No RTK or PPK, flying at 400 ftAbout every 1,000 ft, never moreAerotas
Any corridorAt least every 500 ft on each sidePropeller
Any corridorNo more than 500 to 1,000 ft apart, staggered on long corridorsFHWA
RTK droneA GCP or pair about every 1,500 ft, pairs at both endsAerotas

Keep GCPs off the very edge of the imagery, where overlap is thin. Propeller says each GCP should show up in at least five photos, OpenDroneMap suggests keeping GCPs about 33 to 100 ft (10 to 30 m) in from the project perimeter, and the FHWA warns that points too close to the site edges can cause warping. In the planner, pick the ladder or zigzag layout, set the maximum gap between GCPs (FixFinder's default is 750 ft) and turn on pairs at both ends.

5. Add check shots and plan your base

Check shots are surveyed points you leave out of processing so they can test the result. The planner keeps them inside the project area, between GCPs. For the ground survey itself, plan where RTK corrections come from: NGS guidelines suggest a single base within about 12 miles. Use the nearest base station map to see what is close, and the satellite planner to avoid a poor satellite window on survey day.

6. Fly the sections back to back

Aerotas recommends flying neighboring segments in similar light and conditions, because shadows, mowing or leaf fall between flights can make the overlap fail to match. Take off near the highest point of a segment, or use terrain follow, so overlap stays even over hills.

Quick checklist

  • Corridor KML or KMZ loaded in the mission planner at the full flight width
  • Split into equal sections, about 3,000 ft or less, with about 100 ft of overlap
  • Each section imported into DJI Pilot 2 as a mapping route, flown lengthwise with at least 3 lines
  • GCP pairs every 500 to 1,000 ft (non-RTK) or about 1,500 ft (RTK), pairs at both ends, one GCP in each overlap
  • GCPs in from the edge so each shows in at least five photos; check shots inside the project
  • Base or network within about 12 miles for the GCP survey; pre-flight checklist printed

Price changes and new stations, every two weeks.

New state networks, price changes and plain-language RTK tips. One short email every two weeks, no spam.

Free. We email you a link to confirm. Unsubscribe anytime. Past issues